| |
|
|
 |
       |
| |
Good video quality at a fraction of the cost.
Superior interference immunity.
Transmit video signals longer distances than coaxial cable.
Potential of leveraging existing cable.
Lower labor costs to install vs. coaxial cable {(1) 25 pair UTP pull = (1) coaxial cable pull}.
Higher density and lower weight than coaxial cable. (1/10th the size).
UTP is a multi-use cable (Including Power, Video and Data).
Easier termination than coaxial cable or optical fiber.
Lower cost for conduit and cable trays, uses less space in cable pathways.
Significantly lower cost for low-smoke UTP vs. low-smoke coaxial cable
|
 |
Use Unshielded Twisted Pair, Category 2 or better, 16-24AWG, stranded or solid. Using a multi-pair wire (six pairs or more) with an overall shield is OK. |
|
No, EZLink device is highly immune to interference. CAT 5 UTP twisted pair wire can immunity the RF interference. But the high power (signal noise ratio) RF signal would occur the video interference, neither coaxial nor twisted pair cabling transmission. There three solutions to solve this problem:
When use Coaxial cable: Using Our CS-700RS RF modulator to avoid this problem. I-View's RF modulator allows works with high voltage cable at a time.
When use UTP cable: The most I-View's UTP devices provide the highly immune to interference. That is, the equipment is only concerned with the voltage difference between the two conductors. RF or other fields’ will still couple into the conductors,
but will do so in each conductor equally. This Common-Mode signal is ignored by the I-View equipment, which has a 60 dB Common-Mode Rejection Ratio (CMRR).
|
| |
Provide complete video transmission systems, including UTP, Coaxial and Optical fiber cable solution.
Provide cost efficiency and wide range product series to suit for the difference application.
Products with built-in Surge protection and patented (pending) noise immunity.
All products FCC, CE approved and RoHS compliant.
Technical support and advance replacements on warranty claims.
Simple, intuitive product design permits scalable solutions from 4 cameras to 1000s.
|
| |
A single 4-pair UTP cable run to each camera location allows you to transmit power, video, and data (telemetry).
Plug and play installation.
The PVD system integrates into a structured cabling environment with EIA/TIA 568B standard pin outs.
Open system architecture.
Lower labor and cabling costs compared to coaxial cable.
May be able to leverage existing cable plant.
Fully testable infrastructure via structured cabling testing procedures.
Lower cost solution, better video quality and more reliable than IP systems.
UTP allows for a migration path to IP in the future.
Minimal rack space required.
Centralized power management through UPS at DVR site, no worry for power blackout.
All in one solution (Power/Video/Data), you do not need to set up power cabling for the camera again.
The PVD product series provide lower power (DC48V or AC24/28V); therefore, the installer does not need to have the license of power cabling.
Provide high current (DC12V/1.5A) for long distance (600 meters) power transmission and the power current is enough to support IR camera.
Learn More
|
| |
Analogue camera choices significantly outnumber IP camera choices and are less than half the cost.
Analogue cameras and transmission with DVRs provide more reliable video acquisition, yet permit DVR images to be viewed over a network.
UTP video signals can share the same infrastructure as communication networks.
Minimize IT impact and involvement.
Analog camera continuously record 25/30 FPS high-resolution video without impacting LAN bandwidth.
Only one IP address per DVR vs. individual IP addresses for each IP camera.
Limited points of network vulnerability and highly immune to viruses.
Scheduled network maintenance won’t stop a hybrid system from recording.
Hybrid systems don’t require fiber, 10G Ethernet or parallel networks
No telemetry or video latency issues
Learn More
|
| |
Powering from a central location reduces cabling infrastructure costs and complexity.
Fast, easy installation, save cable and labor costs.
19 inches modularize rack mount deign for easy maintenance.
Build in the Surge protection.
Exceptional interference rejection.
Diagnostic LEDs display load/no load conditions.
Individually floating outputs ensure total ground-loop immunity.
Power 8 (4 x 2) cameras at distance; pass through video and telemetry each via a single 4-pair UTP cable and RJ45 connectivity.
All in one solution (Power/Video/Data), you do not need to set up power cabling for the camera again.
The PVD product series using low power; therefore, the installer does not need to have the license of power cabling.
Provide full range DC48V-12V; AC30V-24V power input.
Provide high current (DC12V/1.5A) for long distance (600 meters) power transmission and the power current is enough to support IR camera.
Learn More
|
| |
Powering from a central location reduces cabling infrastructure costs and complexity.
Fast, easy installation, save cable and labor costs.
Low cost; suit for the small system
Exceptional interference rejection.
Diagnostic LEDs display load/no load conditions.
Individually floating outputs ensure total ground-loop immunity.
Power a camera at distance; pass through video and telemetry each via a single 4-pair UTP cable and RJ45 connectivity.
All in one solution (Power/Video/Data), you do not need to set up power cabling for the camera again.
The PVD product series using low power; therefore, the installer does not need to have the license of power cabling.
Provide full range DC40V-12V; AC30V-24V power input.
Provide high current (DC12V/500mA) for long distance (300 meters) power transmission and the power current is enough to support the most IR camera.
|
|
|
 |
|
 |
|
