Fast Ethernet/PoE Over 2-Wire Extender (STP/UTP Cable Type)
- Transmit up to network speeds up to 150 Mbps** bandwidth, and distance up to 4500ft (1.5Km) suit for the backbone application**.
- Re-use existing coax or any two-wire cable for IP cameras.
- Adapter set to transfer via Ethernet and PoE using any 2-Wire cable.
- Easy to install, no IP and MAC address configuration required.
- Built-in Watchdog can auto-reconnect when system connection fails.
- Compliant IEEE802.3at/af standard and POE+ (50W).
- Instantly check network signals, link, and power status with LED indicators.
- 128-bit AES encrypted communication for transient protection.
Note:** The Power/Distance Calculator can be found at here
i-View’s model EPoC-131 product series Ethernet / PoE Extender system is a compact media converter that allows 10/100 Base-T Ethernet and IEEE802.3at/af, PoE+ power to be transmitted using virtually any kind of cable. It means that you can utilize a Coaxial cable or any two-wire cable (UTP, STP cable, Telephone line, bell wire and power cable for instance) for the Ethernet / PoE Transmission and also use in legacy installations where existing cable is re-deployed as part of an upgrade to IP cameras without having to lay any new cables or implement any other constructional measures. The EPoC-131 product series Ethernet / PoE Extender has the significant additional benefit of the system is that, in addition to data, the power to operate PoE end devices can also be transferred via the two-wire cable. And now with PoE over 2-wire, you can deliver up to PoE+ (50 watts) of PoE power to the camera as well, eliminating the complexity of installing local power supplies. It is hard to predict or measure the length and quality of the installed cable, so it is very important to deliver continuous, reliable power for the new IP camera that the cable you are upgrading. However, thanks to EPoC-131 product series Ethernet / PoE Extender’s ultra-low-power design, even the RG-59 coaxial cable still can support a 25 watt to IP camera at the most range likely to be found in a legacy installation.
Ethernet/PoE over UTP/STP Extender |
|||
Model | EPOC-131VAJ | EPOC-131PSJ | EPOC-131PSJ-O |
Ethernet | |||
Connector | RJ-45 |
||
Connectivity | 10/100 Base-T. auto-negotiation, auto MDI/MDX crossover |
||
Wire type | Cat.5 or better |
||
Distance | 100 Meters (328 feet) |
||
Cable Link | |||
Connector | RJ45 |
||
Type | Receiver | Transmitter | Transmitter |
Wire type | Transmission via Coax |
||
Distance** | Up to 1.5Km (4950 feet) |
||
Topology | Star, Daisy-Chain or any other combination |
||
Encryption | 128-bit AES |
||
Latency | 3ms |
||
Bandwidth** | Total network bandwidth 150 Mbps; with dynamic bandwidth allocation |
||
Power | |||
Power Source | PoE Hub DC44~56V | DC44~56V | DC44~56V |
Power Output | Via STP/UTP (RJ45) | Via PoE (RJ45) | Via PoE (RJ45t) |
Physical | |||
Waterproof | None | None | IP66 |
Dimensions | 100x55x34 (mm) | 100x55x34 (mm) | 128x102x36 (mm) |
Weight | 140g | 140g | 310g |
LED(Status indicator) | Cable link, Ethernet link/activity | Cable link, Ethernet link/activity , Ethernet Power | Cable link, Ethernet link/activity , Ethernet Power |
Environment | |||
Temperature | -5℃~50℃/23°F~122°F (Standard); -40℃~60℃ / -40°F~140°F (Optional: Built-in heater controller) |
||
Humidity | 20% ~ 85% non-condensing |
||
Power consumption | ≤ 1W |
||
Transient immunity | 20µS x5 3,000A, 6,000V; ESD 20KV, 200pF |
||
Certificated | |||
CE, FCC, RoHS. |
|||
Accessories | |||
See the Accessories information |
|||
Note: * Specifications are subject to change without prior notice. ** Distance and number of devices supported may be lower due to power supply capacity and wire voltage-drop. The bandwidth is dynamically allocated (shared based on traffic), and decreases with wire distance. *** EZLink® is the trademark of I-View Communication Inc.; All others trademarks are belonging to the respective owners. |
Data Rate VS. Cable Distance
Power Wattage VS. Cable Distance
Note:
- The above test result table that is NO GUARANTEE of possible cable lengths, data rates, and power transmission, as various physical factors are not within the area of responsibility of i-View.
- The nominal data rate, connection length, and power transmission can only be individually tested and determined at the place of installation.
Fast EPoC Extender System Configuration
(Ethernet/PoE via STP/UTP cable)
Model: RMP-419
1U 19 inches mount panel
- Connectivity for up to 4 units EPoC/EoC devices.
- Combine with EPoC/EoC devices flexibly.
- Maintain easily with modularized design.
- Save maintenance costs by swapping EPoC/EoC units.
- Suit for EoC-100V, EoC-410V, EPoC-131VA and EPoC-131VAJ, EPoC-131VAT and EPoC-151VA units.
- 1U high rack-mountable, weight: 0.35 Kg
Model: DIM-351
35/7.5mm and 35/15mm DIN rail panel.
- Compliant DIN rail standard industrial installation.
- Suit for EPoC-131VA, EPoC-131VAJ, EPoC-131VAT, EPoC-131PS, EPoC-131PSJ, EPoC-PST units.
- Size/Wight: 100mm x47.8mm x10mm / 0.15Kg
Model: PW-4805A
DC48V 24W power supply
- The PW-4805A 24W power supply delivers 48VDC at up to 24 watts for use with Ethernet over 2-wire Extender products.
- Electrical Specifications
Input 100-240VAC 50/60Hz / IEC380-C14 power inlet
Output 48VDC/0.5A (24W) Regulated Class 2 (SELV) / Molded P1J 5.5mm barrel connector / Line cord: 3 ft (1m) long - Product Weight 0.38 Kg
Model: PW-4813A
DC48V 65W power supply
- The PW-4813A 65W power supply delivers 48VDC at up to 65 watts for use with Ethernet over 2-wire Extender products.
- Electrical Specifications
Input 100-240VAC 50/60Hz / IEC380-C14 power inlet
Output 48VDC/1.35A (65W) Regulated Class 2 (SELV) / Molded P1J 5.5mm barrel connector / Line cord: 3 ft (1m) long - Product Weight 0.45 Kg
Model: PW-5613A
DC56V 70W power supply
- The PW-4813A 65W power supply delivers 56VDC at up to 70 watts for use with Ethernet over 2-wire Extender products.
- Electrical Specifications
Input 100-240VAC 50/60Hz / IEC380-C14 power inlet
Output 56VDC/1.28A (70W) Regulated Class 2 (SELV) / Molded P1J 5.5mm barrel connector / Line cord: 3 ft (1m) long - Product Weight 0.45 Kg
Model: TBNC-01
T-type BNC connector
- The Model TBNC-01 is a high-quality T- type adaptor used by i-View EPOC-131series extenders to split data and power signals.
- The TBNC-01 may be used at the head-end or mid-span for coax daisy-chain applications.
- Product weight: 95g
Model: BTB-100
BNC to Screw Terminal Adaptor
- The Model BTB-100 is an adaptor used by i-View EPOC-131series extenders to convert the BNC to the terminal block connection type.
- The BTB-100 may be used mid-span along a wire run whenever conversion between coax and 2-wire cable is required.
- Two screw-terminal connections each support wire diameters as large as 16 AWG (1.3mm) and screws should be torqued to 2 in-lbs (0.2 Nm).
- The BTB-100 is not intended for use with analog video transmission.
- Product weight: 35g
Related Products